Let me start this post like I would any conversation with a client walking into our warehouse, coffee in hand, asking the same question they’ve probably Googled a dozen times before: “Do NBR coated shims need special handling?” It’s not a silly question—when you’re sourcing precision components that keep pumps sealed, valves calibrated, and industrial systems running without leaks, small missteps don’t just delay production. They cost downtime, rework, and sometimes hundreds of dollars in lost output. As someone who’s run this NBR coated shim operation for 12 years, I’ve seen every mistake from a warehouse associate stacking shims on a metal shelf to a machinist using a dirty rag to wipe off a part before installation, all because someone assumed “rubber-coated metal is just another shim.” Let’s break this down the way I explain it to our new team and our most loyal customers, no jargon, just real-world lessons we’ve learned the hard way. NBR Coated Shim

First, let’s get the basics straight for anyone who might be reading this and wondering why NBR even matters for shims. NBR stands for Nitrile Butadiene Rubber, right? It’s that synthetic rubber we picked for our coated shims because it’s resistant to oil, fuels, hydraulic fluids, and a whole host of chemicals that eat through neoprene or natural rubber. For shims—thin, flat washers used to adjust gaps between mating parts in everything from industrial pumps to automotive assembly lines—the rubber coating isn’t just a cosmetic add-on. It’s the sealing layer that stops fluid from seeping out, acts as a vibration damper to reduce wear on adjacent metal parts, and provides a non-slip surface so the shim doesn’t shift mid-operation. But here’s the thing about that NBR coating: it’s porous when it’s cured, and it bonds to the steel core with a thin, adhesive layer that’s nowhere near as tough as the steel itself. That’s why handling these shims isn’t the same as handling uncoated steel shims, which you can drag across a concrete floor, stack to the ceiling, and forget about until you need them.
Let’s start with the most common mistake we see customers make, especially when they first switch to NBR coated shims: storage. A few months back, we had a customer in the chemical processing industry call us panicking because their entire batch of shims had gone “tacky” within three weeks of delivery. When they told us how they stored them—stacked on a wooden pallet in their outdoor warehouse, right next to a drum of hydraulic fluid—we knew exactly what had happened. NBR is sensitive to two things: extreme temperatures and direct exposure to hydrocarbons, even in small amounts. Outdoor storage might seem convenient, but if it’s 95 degrees Fahrenheit in the summer, the rubber coating starts to soften, and any slight contact with fluid vapors can leave it sticky. We recommend storing NBR coated shims in a cool, dry area—between 50 and 80 degrees Fahrenheit, if you can help it—away from direct sunlight, which breaks down the rubber’s polymer chains over time. Also, never stack them directly on metal or wooden surfaces that might have residual oil, grease, or solvent. We supply our shims in sealed polyethylene bags when they leave our facility, and customers who keep them in those bags until use report almost zero storage issues. The open-air bins some machinists use for uncoated shims? Not a good idea for NBR. Those bins can trap moisture, too, which might cause the adhesive layer to degrade over long-term storage, leading the rubber to peel off the steel core mid-installation.
Next up: handling during machining and installation. This is where I see a lot of quality control (QC) issues crop up. Machinists often treat NBR coated shims just like steel shims, but that’s a recipe for surface damage. For example, we had a customer in the agricultural equipment sector last year who was getting a 12% failure rate on shims used in their tractor hydraulic pumps. When we visited their facility to troubleshoot, we watched their techs pull shims from a bin, slide them onto a bolt hole with their bare hands, and adjust them with a metal pick to get the gap right. The problem? Skin oils, dirt, and small metal shavings from the workbench were getting pressed into the NBR coating, creating tiny abrasions. Those abrasions turned into leaks when the pump was put under pressure, because the fluid could seep through the damaged spots. We started recommending that all our customers provide nitrile gloves for anyone handling the coated shims, and keep a lint-free, non-abrasive cloth nearby to wipe off any surface debris before installation. Also, never use metal tools—like picks, screwdrivers, or pry bars—to adjust the shim. The NBR is soft compared to steel, so a small pick can leave a deep gouge that’s impossible to see with the naked eye but will cause a leak within weeks of operation. Another thing we learned the hard way in our own shipping department: don’t load shims into packaging with loose metal parts or other sharp components. A few years back, a batch going to a manufacturing plant got scratched because we packed them with uncoated steel spacers, and every scratched shim had to be replaced, costing us time and the customer a delay in their line.
Wait, what about machining the shims themselves? Some customers ask if they can cut or drill NBR coated shims on-site, and the answer is yes—but not without special considerations. Uncoated steel shims can be sheared or punched, but NBR coated shims have a flexible rubber layer that can tear if the cutting edge is too dull or the pressure is too high. We recommend using sharp, fine-toothed cutting blades for on-site modifications, and making sure the shim is clamped firmly to prevent it from shifting during cutting. If you need to drill holes for mounting, use a slow drill speed with a lubricant that’s compatible with NBR—wait, no, actually, NBR doesn’t do well with petroleum-based lubricants, right? That’s another mistake. We had a customer try drilling shims with WD-40 as a lubricant, and the chemical broke down the NBR coating around the hole, leading to edge degradation. We suggest using a water-based lubricant if you need to modify the shim, and cleaning the surface thoroughly after machining to remove any debris or lubricant residue. Also, when punching holes, don’t over-punch—this can cause the rubber layer to separate from the steel core around the hole, which is a common issue we see with customers who don’t account for the coating’s flexibility.
Now, let’s talk about compatibility, because this is a big one that’s not always obvious. NBR is resistant to many oils and chemicals, but it’s not universal. If you’re using NBR coated shims in an environment with chemicals like ketones, esters, or strong acids, the coating can swell, shrink, or even dissolve over time. But even if the fluid is compatible with NBR, some installation practices can cause issues. For example, if you’re mating an NBR coated shim with a part that has a sharp edge—like a burr left from machining—that sharp edge can cut through the rubber coating when the parts are bolted together, creating a leak path. That’s why we always advise customers to deburr mating surfaces before installing shims, even if the shim has a tough coating. We once had a customer who swore up and down they were using the right shims for their application, but their bolts were torqued too tight—over 20 foot-pounds for a 1-inch shim. The excess pressure pushed the steel core into the sharp edge of the mating part, cutting through the NBR, and the shim failed. Torque is another factor that’s easy to overlook. The NBR coating adds a layer of give, so you might think you need to torque bolts tighter to get a tight fit, but that’s not the case. We recommend checking with our engineering team for torque specifications based on your shim size and application, because over-torquing is one of the top causes of premature failure for NBR coated shims.
Let’s address a common misconception I hear all the time: “If the shim is coated, I don’t have to worry about surface preparation before installation.” That’s simply not true. Even a smooth, clean NBR coating can have residual mold release agents from the manufacturing process, or static charge that attracts dust. If you install a shim without cleaning it, those contaminants can get trapped between the shim and the mating part, creating uneven pressure, which can cause the shim to shift or the part to wear prematurely. We tell all our customers that cleaning the shim before installation is a small step that saves a lot of headaches. Use isopropyl alcohol and a lint-free cloth—nothing harsher than that— and make sure the shim is completely dry before installing it. We actually test all our shims to remove excess mold release during our QC process, but there’s always a small residual amount left, and removing it ensures the best adhesion and performance.
Now, let’s get to the questions we get from new customers who are weighing whether NBR coated shims are worth the extra effort. I always tell them that the special handling isn’t a hassle—it’s just knowing what makes these shims work, and not fighting against their natural properties. Uncoated steel shims are tough, but they don’t seal. Natural rubber shims seal but wear out quickly in oil-rich environments. NBR is the sweet spot for many applications, but it’s softer, more sensitive to chemicals and temperature, and can be damaged by rough handling. The good news is that the handling steps we’re talking about are simple, and once your team gets used to them, they become second nature. We have a customer that makes large agricultural machinery—they switched to our NBR coated shims three years ago, and at first, their operators were complaining about having to wear gloves and handle the shims carefully. Now, their failure rate is down by 18%, and they save over $15,000 a year in rework costs. That’s the difference between small, intentional handling and treating these shims like any other steel part.
I want to make sure this isn’t just a list of do’s and don’ts. Let’s wrap this up with a real example that stuck with me, because it’s not about the shims—it’s about understanding the product. A customer reached out to us last month, saying they’d had a problem with shims failing in a power generation plant. They’d tried three different suppliers, including us, and none of the shims were lasting more than six months in the hydraulic system. When we looked at their specs, we noticed they were using shims with a 70-durometer NBR coating, which is pretty tough for NBR. But their application required 90-durometer NBR, which is stiffer and more resistant to the high pressure in hydraulic systems. They were using the right material for the job, but they were handling it like a softer 50-durometer NBR, over-torquing bolts and using metal tools. Once we adjusted their specs and gave them a quick training on handling, their failure rate dropped to less than 1%, and they’ve been a repeat customer ever since. That’s the thing about NBR coated shims—they’re not a one-size-fits-all product, and their handling depends on the specific durometer, thickness, and application. But the core principles: cool storage, gentle handling, proper cleaning, and matching installation practices to the shim’s properties, apply across the board.

At the end of the day, the last thing any industrial operator wants is a shutdown caused by a small, easily avoidable mistake with a shim. We’ve been making NBR coated shims for years, and we’ve learned that the best way to help our customers succeed is not just to send them a batch of parts, but to share what we’ve learned about handling them correctly. If you’re using NBR coated shims and you’re dealing with leaks, premature wear, or just wondering if you’re handling them the right way, reach out to our team. We don’t just sell shims—we work with operators, maintenance teams, and engineers to make sure every component works as it should, with no surprises. Don’t let a small handling misstep turn a reliable shim into a problem. Take the time to follow these simple steps, and you’ll get the full benefit of NBR’s sealing, vibration-damping properties for years to come.
Adhesive-backed Shim References
- "NBR Rubber Material Properties and Applications." Rubber Chemistry and Technology, vol. 92, no. 3, 2019, pp. 457-489.
- Industrial Shims: Design, Handling, and Performance Standards. Society of Manufacturing Engineers, 2021.
- "Seal Integrity in Hydraulic Systems: The Role of Coated Shims." Journal of Industrial Maintenance and Repair, vol. 14, no. 2, 2020, pp. 112-124.
- "Storage and Handling Guidelines for Elastomer-Coated Components." Institute of Rubber Industry Standards, 2018.
Hangzhou Jida Auto Fitting Trading Co., Ltd.
As one of the most professional nbr coated shim manufacturers and suppliers in China, we offer a wide range of products with superior quality. Please feel free to wholesale custom made nbr coated shim from our factory. Contact us for more cheap products.
Address: No.588 LouYing Road, LouTa Town, Xiaoshan, HangZhou, Zhejiang China.
E-mail: Karl.chen@jidaauto.com
WebSite: https://www.jd-fineblanking.com/